11/12/2023 0 Comments Create samba share ubuntu 20.04![]() ![]() This will serve to demonstrate that you are in the remote folder. In this case, we will give you read and write permissions. Then assign the corresponding permissions. As we want it to be a public folder, we will tell the system that it does not have an owner and that it does not belong to a system group either sudo chown -R nobody:nogroup /var/public Now it is necessary to indicate the owner of the folder. This is not always recommended but there are cases where it can be quite useful.įirst, create the folder with the name you want in the chosen path. Public folders have one advantage and that is that we can enable guest or anonymous access. ![]() In both cases, it will be hosted on a server with IP address 192.168.1.43 Configure Samba and a public folder In this post, you will learn how to configure Samba for a public and a private folder. This is recommended because if something bad happens we can always reverse the changes. It is a well-documented file that just by reading it we will know how to manipulate.įirst, make a backup of the file. Configuring Samba on Ubuntu 20.04īy default, the Samba configuration file is /etc/samba/smb.conf. This way it will be installed, but it is missing configuration. To check the status of the service you can run: sudo systemctl status smbd To start the service and make it start together with the system, execute these commands: sudo systemctl start smbd Start a terminal or SSH session and run the following commands: sudo apt update So, Samba is present in the official Ubuntu repositories so the installation becomes easy. Therefore it is available for many Linux distributions. This protocol is very mature and is quite simple to configure. That is, with Samba we can share files between computers on a network. Samba is a free implementation of the Microsoft Windows file-sharing protocol (formerly called SMB, recently renamed to CIFS) for UNIX-like systems. That’s why after reading this post, you will learn how to install and configure Samba to share files on a network. However, it is also useful when we have several computers within the same network as in a house. winServerName/shareName /media/mountName cifs credentials=/home/userId/.smbcredentials,uid=1000,gid=1000,vers=3.Installing and configuring Samba in Ubuntu 20.04 is a typical task of a sysadmin. The ‘id’ command will output something similar to the following: uid=1000(userId) gid=1000(userId) groups=1000(userId),4(adm),………….,1001(smbgroup)īackup and edit ‘fstab’ to mount window share at ubuntu startup Sudo chmod 600 ~/.smbcredentials retrieve ‘uid’ and ‘gid’ values for next step Set permissions to hide username and password Sudo nano ~/.smbcredentials enter the following 2 lines username=windowsLoginIdĮnter 'ctrl-x', then 'y' and finally 'enter' to exit and save file Sudo chmod 755 /media/mountName create ‘credentials’ file to hold userid/password and set permissions Sudo chown userId:userId /media/mountName Sudo apt-get install cifs-utils create mount points for windows shares and set permissions Xrdp, samba-common, samba, smbclient open ‘Terminal’ and enter the following commands: install cifs utilities after new Ubuntu install, additional packages to add: Source: Ubuntu Server 18.04.01 LTS CIFS Mount failing Source: How to change permissions on mounted windows share? If you do not need this capability omit this package from the first step everything else should still work.Īll the steps listed are what I actually used. Xrdp, which enables remote desktop access to a ubuntu-pc, was used in all my installations. You could give it a try if that’s what you want. When I started to solve this problem my mount points were setup in the ‘/mnt/‘ folder, as of now I am not sure if that will still work. The steps below have the mount points in the ‘/media/‘ folder, this follows what was recommended on some source webpages. In my experience hard drives have faster write speeds and usually last longer than ssd drives. The hard drives are needed since they are to be used for extensive i/o. Unfortunately, Microsoft discourages using passthrough hard drives and this caused me to look for a linux solution. ![]() This solution solves a similar problem in Hyper-V when using ‘passthrough hard drives’ the Ubuntu vm's have only ‘read’ permissions on the hard drives. So far the network shares popup quickly and there is no appreciable lag times when traveling up and down the directory trees. This solution has been installed and working on three ubuntu VM’s that are running under Windows 10 Pro Hyper-V and Ubuntu 20.04 KVM VMM. The notes have gone thru a few revisions and for reference there are 4 sources for further reading. After writing up my notes for future reference, I decided to post them here to help anyone who might have similar problems. I spent countless hours and visited numerous webpages to what I thought would be a straight forward problem. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |